Free · English and ಕನ್ನಡ
Borewell Motor HP Calculator
How much HP motor is required for your borewell? Enter the pump depth in feet and the inches of water. See the submersible motor HP you need, worked out from pump makers’ charts, and the BTCO starter that protects it from burning.

Don’t know? Enter the borewell depth. The answer will be a little on the safe side.ಗೊತ್ತಿಲ್ಲವೇ? ಬೋರ್ವೆಲ್ ಆಳ ಹಾಕಿ. ಉತ್ತರ ಸ್ವಲ್ಪ ಸುರಕ್ಷಿತ ಕಡೆಗೆ ಇರುತ್ತದೆ.
The inches the driller measured when the borewell was dug.ಬೋರ್ ಕೊರೆಸಿದಾಗ ಅಳೆದ ಇಂಚು ನೀರು.
Motor you needನಿಮಗೆ ಬೇಕಾದ ಮೋಟಾರ್
7.5 HP
3 phase motor · about 3,400 litres an hour from 400 ft
How much HP motor is required for your borewell depth
This borewell motor HP chart (submersible pump HP vs depth) is worked out the same way as the calculator. Find your pump depth on the left, from 100 to 1300 feet, and the water at the top. In deep borewells the depth decides the motor much more than the water does.
On a phone, swipe the chart sideways.
| Pump depth | Up to 2" water up to about 3,400 L/hr | 2½" water about 5,900 L/hr | 3" water about 9,300 L/hr |
|---|---|---|---|
| 100 feet | 3 HP | 3 HP | 3 HP |
| 200 feet | 3 HP | 5 HP | 5 HP |
| 300 feet | 5 HP | 7.5 HP | 7.5 HP |
| 400 feet | 7.5 HP | 7.5 HP | 10 HP |
| 500 feet | 7.5 HP | 10 HP | 12.5 HP |
| 600 feet | 10 HP | 10 HP | 15 HP |
| 700 feet | 10 HP | 15 HP | 15 HP |
| 800 feet | 15 HP | 15 HP | 17.5 HP |
| 900 feet | 15 HP | 17.5 HP | 20 HP |
| 1000 feet | 17.5 HP | 20 HP | 25 HP |
| 1100 feet | 25 HP | 25 HP | 25 HP |
| 1200 feet | 25 HP | 25 HP | 30 HP |
| 1300 feet | 30 HP | 30 HP | 30 HP |
Up to 2 inches the answer is the same, because borewell pumps for these depths are not made for less water than that. With 1 or 1½ inches, the pump will pump the borewell empty, so the starter must stop it when the water runs out.
1 inch and 2 inch borewell water in litres
When a borewell is drilled, the driller lets the water flow out over a V shaped notch and calls the height of the water “inches”. This is how those inches turn into litres:
| Water | Litres per hour | Litres per minute |
|---|---|---|
| 1" | about 597 | about 10 |
| 1½" | about 1,650 | about 28 |
| 2" | about 3,382 | about 56 |
| 2½" | about 5,919 | about 99 |
| 3" | about 9,329 | about 155 |
How to calculate motor HP for a borewell
- Lift: the pump depth you enter, plus 5% for the water rubbing along the pipe and 3 metres to bring it out at the top.
- Pump makers’ charts: we read the performance tables of 569 six inch borewell pumps from three Indian makers. For every motor size, they show how high its pumps lift water at each flow.
- 10% spare: the lift is raised by 10%, so the pump still delivers when it gets older or the voltage is low.
- Motor size: the answer is the smallest motor whose pumps reach that lift with your water: 3, 5, 7.5, 10, 12.5, 15, 17.5, 20, 25 or 30 HP.
Want the full explanation, with the borewell’s yield and the water level while pumping? Read how much HP motor does my borewell need.
A bigger motor is not a safer motor
It is tempting to buy one size up “to be safe”. But a motor that pumps faster than the borewell refills pulls the water below the pump. The pump then runs dry, and a submersible motor running dry has no water to cool it. This is one of the most common reasons submersible motors burn.
Whatever HP you choose, the starter is what saves the motor. Every BTCO starter has dry run protection: it stops the motor when the water runs out and starts it again after a waiting time you set. It also protects against overload, single phasing and voltage fluctuation, so the motor is stopped before it burns. In summer, read protecting your motor when the water level drops.
Which BTCO starter for your HP
- Single Phase starter: single phase motors, 2 to 5 HP. Single phase motors are not made above 5 HP, and 5 HP is rare.
- DOL starter: 3 phase single cable motors, 3 to 10 HP.
- Star Delta starter: 3 phase double cable motors, 7.5 to 30 HP.
- On juice line or 2 phase, a Combined starter runs your 3 phase motor. See DOL vs star delta if you are not sure about your cable.
Next, check the cable: a cable that is too thin for a deep borewell also burns motors. Use the submersible cable size calculator.
Frequently asked questions
How much HP motor is required for a 200 feet borewell?
About 3 HP for up to 2 inches of water, and 5 HP for 2½ to 3 inches. At this depth a single phase motor of 3 HP can also work.
How much HP motor is required for a 500 feet borewell?
With the pump at 500 feet, about 7.5 HP for up to 2 inches of water, 10 HP for 2½ inches and 12.5 HP for 3 inches. These come from pump makers’ charts with 10% spare. Use the calculator above for your own depth.
How much HP motor is required for a 700 feet borewell?
About 10 HP for up to 2 inches of water, and 15 HP for 2½ to 3 inches. This needs a 3 phase motor.
How much HP motor is required for a 1000 feet borewell?
With the pump at 1000 feet, about 17.5 HP for up to 2 inches of water, 20 HP for 2½ inches and 25 HP for 3 inches. Motors this big are 3 phase and double cable, so they use a star delta starter.
How much HP motor is required for a 1300 feet borewell?
About 30 HP. At 1300 feet the depth decides the motor more than the water: borewell pumps up to 25 HP don’t lift water that high with spare left over.
How many litres is 1 inch of borewell water?
About 600 litres an hour (10 litres a minute). 2 inches is about 3,400 litres an hour and 3 inches about 9,300 litres an hour. These are the figures used when a driller measures the water flowing out of a new borewell.
Why does 1 inch of water need the same motor as 2 inches?
Borewell pumps for deep borewells are not made for less than about 50 litres a minute, which is close to 2 inches. So the depth decides the motor. With only 1 or 1½ inches, that pump empties the borewell and runs dry, so dry run protection is a must.
Can I use a single phase motor?
Only for shallow borewells. Single phase borewell motors are not made above 5 HP, and 5 HP single phase motors are rare. With the pump deeper than about 300 feet you need a 3 phase motor and a 3 phase supply.
Should I enter the borewell depth or the pump depth?
The pump depth, if you know it: that is the height the pump must lift the water. If you don’t know it, enter the borewell depth. The answer will then be on the safe side.
Which starter do I need for my motor?
Single phase motors of 2 to 5 HP take the BTCO Single Phase starter. 3 phase single cable motors of 3 to 10 HP take the DOL starter, and double cable motors from 7.5 HP to 30 HP take the Star Delta starter. The starter finder picks the right one in a few questions.
Please note: these are approximate values, not exact ones. They are general information, not a BTCO recommendation. Every borewell, motor and pump is different, so please contact your motor dealer for values made for your borewell before you buy. The HP figures come from published pump charts.